Omnimark Mark 3 [reconditioned]

$5,500.00

Omnimark Mark3 Moisture Analyzer - [Reconditioned/Used]

$5500.00

Description:

  • Omnimark Moisture/Solids analyzer
  • Thermally isolated balance with superior low level moisture performance of less than 50 ppm
  • Up to four heater modules can be run with one control module
  • Serial, USB and Ethernet for bi-directional connectivity
  • Built-in temperature and weight calibration feature
  • Quarter VGA screen for easy viewing
  • Large storage of methods for easy recall of known drying procedures
  • Improve process control
  • Increase profits
  • Durable construction
  • Complies with AOAC Official Methods
  • Languages: English

Specifications

  • Display of Results 0.01% 0.001%
  • Balance Resolution 0.001 grams 0.0001 grams
  • Balance capacity 100 grams 100 grams
  • Balance repeatability +/-0.5mg +/-0.1mg
  • Method of Measurement: Loss on Drying
  • Modular configuration: Control and Heater modules (Optional: up to 4 Heating modules)
  • Heat Source: Four parallel infrared quartz cylinders
  • Temperature Setting/Control: 30-210C in one degree increments/RTD sensor, +/- 1C
  • Temperature Steps: Programmable one or two with selectable ramp rate
  • Temperature Adjustment: Optional fixture for Internal electronic two point adjustment
  • Standby Temperature: 30-160C in one degree increments with selectable equilibration time
  • Temperature display: Display of both target and current temp at each stage of drying and standby
  • Conserve Mode Clock: Programmable time by day of week to shut down and wake up analyzer
  • Balance Calibration: Internal calibration weight or external manual
  • Ideal Weight: Audio and visual display for programmable target sample weight addition
  • Target limit alert: Minimum and maximum programmable limits and screen alert when test done
  • Program Storage: 300 programs with unique settings, alphanumeric naming
  • Result Storage: 999 results with statistics: Average, SD, RSD, high and low
  • Units of Measure of Results: Weight, %Moisture, %Solids, %Volatiles, Fuel Moisture, PPM
  • Endpoint Determination: Actual slope, Calculation and Time modes
  • Sample ID: Numeric, Numeric incrementing, alphanumeric or turned Off
  • Modes of Operation: Standard test, Syringe or Concentration modes
  • Operator Names: Twenty alphanumeric operator names
  • Security Mode: Selectable setup and operation protection with passcode
  • Graph Mode: Graph of Temperature/time and Percent/time
  • Display: Quarter VGA with contrast adjustment (black on white or white on black)
  • Keypad: Sealed membrane with audible tactile feedback
  • Internal Printer: Thermal, 40 character graphic with selectable format
  • External Input/Output: Serial, USB and Ethernet
  • Internal Clock: Date and Time: U.S. or International, Military or AM/PM
  • Audible Tone: Key stoke, ideal weight met and end of test, selectable On or Off
  • System Status Indicator Lights: Two tri-color LEDs (balance & heater) on front of Heater module

Electrical Requirement:

  • Power Requirements: 100-120/200-240V~ 5A T
  • Dimensions (L x W x H): 16 1/4 x 19 1/2 x 9 1/4" (41.3 x 49.5 x 23.5cm) Modules combined
  • Weight: 22 lbs. (10Kg)

Omnimark Mark 3, Mark3, Mark 3, Omnimark Mark3, Mark-3, Omnimark-Mark3

Instruments listed above are registered trademark of their respective corporation.


Add to Cart:

  • Model: Mark 3
  • Shipping Weight: 30lbs
  • Manufactured by: Omnimark Corporation


This product was added to our catalog on Thursday 07 July, 2011.

Copyright © 2014 Laboratory Instrument Specialists. Powered by HenaStudio.com